Troubleshooting Varnish

Sometimes Varnish misbehaves or rather behaves the way you told it to behave but not necessarily the way you want it to behave. In order for you to understand whats going on there are a couple of places you can check. varnishlog, /var/log/syslog, /var/log/messages are all good places where Varnish might leave clues of whats going on. This section will guide you through basic troubleshooting in Varnish.

When Varnish won’t start

Sometimes Varnish wont start. There is a plethora of possible reasons why Varnish wont start on your machine. We’ve seen everything from wrong permissions on /dev/null to other processes blocking the ports.

Starting Varnish in debug mode to see what is going on.

Try to start Varnish by:

# varnishd -f /usr/local/etc/varnish/default.vcl -s malloc,1G -T 127.0.0.1: 2000  -a 0.0.0.0:8080 -d

Notice the ‘-d’ parameter. It will give you some more information on what is going on. Let us see how Varnish will react when something else is listening on its port.:

# varnishd -n foo -f /usr/local/etc/varnish/default.vcl -s malloc,1G -T 127.0.0.1:2000  -a 0.0.0.0:8080 -d
storage_malloc: max size 1024 MB.
Using old SHMFILE
Platform: Linux,2.6.32-21-generic,i686,-smalloc,-hcritbit
200 193
-----------------------------
Varnish Cache CLI.
-----------------------------
Type 'help' for command list.
Type 'quit' to close CLI session.
Type 'start' to launch worker process.

Now Varnish is running but only the master process is running, in debug mode the cache does not start. Now you’re on the console. You can instruct the master process to start the cache by issuing “start”.:

start
bind(): Address already in use
300 22
Could not open sockets

And here we have our problem. Something else is bound to the HTTP port of Varnish. If this doesn’t help try strace or truss or come find us on IRC.

Varnish is crashing - panics

When Varnish goes bust the child processes crashes. Most of the crashes are caught by one of the many consistency checks we have included in the Varnish source code. When Varnish hits one of these the caching process will crash itself in a controlled manner, leaving a nice stack trace with the mother process.

You can inspect any panic messages by typing panic.show in the CLI.:

panic.show
Last panic at: Tue, 15 Mar 2011 13:09:05 GMT
Assert error in ESI_Deliver(), cache_esi_deliver.c line 354:
  Condition(i == Z_OK || i == Z_STREAM_END) not true.
thread = (cache-worker)
ident = Linux,2.6.32-28-generic,x86_64,-sfile,-smalloc,-hcritbit,epoll
Backtrace:
  0x42cbe8: pan_ic+b8
  0x41f778: ESI_Deliver+438
  0x42f838: RES_WriteObj+248
  0x416a70: cnt_deliver+230
  0x4178fd: CNT_Session+31d
  (..)

The crash might be due to misconfiguration or a bug. If you suspect it is a bug you can use the output in a bug report, see the “Trouble Tickets” section in the Introduction chapter above.

Varnish is crashing - segfaults

Sometimes a bug escapes the consistency checks and Varnish gets hit with a segmentation error. When this happens with the child process it is logged, the core is dumped and the child process starts up again.

A core dumped is usually due to a bug in Varnish. However, in order to debug a segfault the developers need you to provide a fair bit of data.

  • Make sure you have Varnish installed with debugging symbols.

  • Make sure core dumps are allowed in the parent shell. (ulimit -c unlimited)

Once you have the core you open it with gdb and issue the command bt to get a stack trace of the thread that caused the segfault.

Varnish gives me Guru meditation

First find the relevant log entries in varnishlog. That will probably give you a clue. Since varnishlog logs a lot of data it might be hard to track the entries down. You can set varnishlog to log all your 503 errors by issuing the following command:

$ varnishlog -q 'RespStatus == 503' -g request

If the error happened just a short time ago the transaction might still be in the shared memory log segment. To get varnishlog to process the whole shared memory log just add the ‘-d’ parameter:

$ varnishlog -d -q 'RespStatus == 503' -g request

Please see the vsl-query and varnishlog man pages for elaborations on further filtering capabilities and explanation of the various options.

Varnish doesn’t cache

See Achieving a high hitrate.